Alex Rivera | Logout

how do you diagnose a kernel oops?

Asked 2008-11-25T01:52:30.810
21

Given a linux kernel oops, how do you go about diagnosing the problem? In the output I can see a stack trace which seems to give some clues. Are there any tools that would help find the problem? What basic procedures do you follow to track it down?


Unable to handle kernel paging request for data at address 0x33343a31
Faulting instruction address: 0xc50659ec
Oops: Kernel access of bad area, sig: 11 [#1]
tpsslr3
Modules linked in: datalog(P) manet(P) vnet wlan_wep wlan_scan_sta ath_rate_sample ath_pci wlan ath_hal(P)
NIP: c50659ec LR: c5065f04 CTR: c00192e8
REGS: c2aff920 TRAP: 0300   Tainted: P          (2.6.25.16-dirty)
MSR: 00009032   CR: 22082444  XER: 20000000
DAR: 33343a31, DSISR: 20000000
TASK = c2e6e3f0[1486] 'datalogd' THREAD: c2afe000
GPR00: c5065f04 c2aff9d0 c2e6e3f0 00000000 00000001 00000001 00000000 0000b3f9
GPR08: 3a33340a c5069624 c5068d14 33343a31 82082482 1001f2b4 c1228000 c1230000
GPR16: c60f0000 000004a8 c59abbe6 0000002f c1228360 c340d6b0 c5070000 00000001
GPR24: c2aff9e0 c5070000 00000000 00000000 00000003 c2cc2780 c2affae8 0000000f
NIP [c50659ec] mesh_packet_in+0x3d8/0xdac [manet]
LR [c5065f04] mesh_packet_in+0x8f0/0xdac [manet]
Call Trace:
[c2aff9d0] [c5065f04] mesh_packet_in+0x8f0/0xdac [manet] (unreliable)
[c2affad0] [c5061ff8] IF_netif_rx+0xa0/0xb0 [manet]
[c2affae0] [c01925e4] netif_receive_skb+0x34/0x3c4
[c2affb10] [c60b5f74] netif_receive_skb_debug+0x2c/0x3c [wlan]
[c2affb20] [c60bc7a4] ieee80211_deliver_data+0x1b4/0x380 [wlan]
[c2affb60] [c60bd420] ieee80211_input+0xab0/0x1bec [wlan]
[c2affbf0] [c6105b04] ath_rx_poll+0x884/0xab8 [ath_pci]
[c2affc90] [c018ec20] net_rx_action+0xd8/0x1ac
[c2affcb0] [c00260b4] __do_softirq+0x7c/0xf4
[c2affce0] [c0005754] do_softirq+0x58/0x5c
[c2affcf0] [c0025eb4] irq_exit+0x48/0x58
[c2affd00] [c000627c] do_IRQ+0xa4/0xc4
[c2affd10] [c00106f8] ret_from_except+0x0/0x14
--- Exception: 501 at __delay+0x78/0x98
    LR = cfi_amdstd_write_buffers+0x618/0x7ac
[c2affdd0] [c0163670] cfi_amdstd_wr
Edit
Report

1 Answer

5

You should first try to find the source of the code that has crashed. In the specific case, the analysis claims that the crash happened in mesh_packet_in of the manet driver, at offset 0x8f0. It also reports that the instructions at this point are 419d02a0 98010009 ... So inspect the module with "objdump -d", to confirm whether the function/offset reported is correct. Then check the source for what it is doing; you can use the registers list to confirm again that you are looking at the right instruction.

When you know what C statement is faulting, you need to read the source to find out where the bogus data were coming from.

answered 2008-11-25T04:38:19.850

Your Answer